Hỗ trợ trực tuyến

KellyMoore 98-001 (4 Lít) Sơn Lót Ngoại Thất Chống Kiềm (PH11)

Miêu tả:

Sơn lót Kelly Moore Stucco Seal ngoại thất có độ bền cao và chất lượng cao, tạo nên màng sơn với khả năng ngăn chặn sự muối hoá và sự xuống cấp cuả màng sơn phủ do chất kiềm trong xi măng gây ra, tăng khả năng kháng kiềm lên tới nồng độ PH11. 
Quy Cách:

98-001 (1L)  Sơn Lót Tường Chống Kiềm Ngoại Thất 1 Lít   156,520 VND/ Thùng 1 Lít
98-001 (4L)  Sơn Lót Tường Chống Kiềm Ngoại Thất  4 Lít  482,138 VND/ Thùng 4 Lít
98-001 (19L)  Sơn Lót Tường Chống Kiềm Ngoại Thất  19 Lít  2,034,588 VND/ Thùng 19 Lít


Product Description
A professional quality, exterior, low viscosity acrylic,
penetrating clear sealer. Designed to seal stucco,
concrete and masonry surfaces. Used as an
excellent undercoat for elastomeric and conventional
coatings. Features high alkali resistance when
applied to surfaces with a pH level up to 11 and good
chalk binding properties. Stucco Seal is suitable as
an anti-dusting sealer when applied to properly
prepared, un-sealed concrete floors. Excellent for
commercial and residential application.


Performance Features
  Excellent Adhesion
  Excellent Alkaline Resistance
  Ties Down Light Chalk
  Paintable
  Anti-Dusting Sealer for Concrete Floors

Product  Specifications
Resin Type:  Acrylic
Color Range:  Clear
Drying Time:
(75º F. & 50% R.H.)
To touch: 30 minutes
To recoat: 2-4 hours.
Practical Coverage:  Approx. 100-250 sq ft/gallon
Recommended Dry
Film Thickness:
0.8-1.0 mils per coat
(theoretical, penetrating product)
Weight per Gallon:  8.5 lbs.
Solids by Weight: 23%
Solids by Volume:  21%
Shelf Life:  2 years (unopened containers)
Sizes:  One & five gallon containers
V.O.C. <100 Grams per liter
Clean Up:   Water

Product Analysis (by weight)
PIGMENT COMPOSITION 0%
VEHICLE COMPOSITION 100%
Acrylic Resin: 23%
Water, Surfactants, Defoamers: 77%


Surface Preparation
WARNING! If you scrape, sand or remove old paint
from any surface, you may release lead dust. LEAD
IS TOXIC. EXPOSURE TO LEAD DUST CAN
CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Carefully clean up with a wet
mop or HEPA vacuum. Before you start, find out how
to protect yourself and your family by contacting the
U.S. EPA/Lead Information Hotline at 1-800-424-
LEAD (5323) or log on to www.epa.gov/lead.
General: 
All surfaces must be cured, firm, dry and cleaned free
of dust, dirt, oil, grease, wax, chalky or loose paint,
rust, loose mill scale, bond breakers and curing
compounds, efflorescence, asphalt stains, mildew or
any other contamination or condition that would
adversely affect the performance of the coating. Sand
glossy, glazed or dense surfaces. Fill holes and
surfaces irregularities with a suitable patching
compound to match the surface profile. 
Concrete Floors: Floor should be unsealed and free of
all contaminants. If the floor is dense and non-porous,
acid etching may be required to allow penetration.
System Recommendations 
Concrete, Masonry, Stucco & Plaster:
PRIMER: 98  Stucco Seal

FINISH:  98 Stucco Seal or other appropriate
Kelly-Moore acrylic or elastomeric finish.
Concrete Floors:
FINISH:  98 Stucco Seal

Application
Brush, roll or spray. Do not apply when material, air,
and/or surface temperature is below 50°F or if rain is
imminent. Extremely high or low temperature or
periods of high relative humidity may adversely affect
dry time. Do not allow material to pond on concrete
floors. Stir thoroughly before and during use.
Maintain a wet edge to avoid lap marks.

Thinning
Apply at can consistency.
Precautions
Avoid contact with eyes, skin and clothing.  Do not
take internally. Wash thoroughly after handling. 
Close container after each use. Protect from freezing. 
For additional safety information, consult the Material
Safety Data Sheet for this product..
USE ONLY WITH ADEQUATE VENTILATION.
KEEP OUT OF REACH OF CHILDREN.

Proper Disposal
For proper disposal of excess material, please
contact your local city or county waste management
agency.

Mildew: This paint has been formulated to be mildew
resistant, however, it will not mildew-proof the surface nor
completely prevent or destroy mildew. Therefore, Kelly-
Moore Paint Company Inc. assumes no responsibility for
mildew development.
Limited Warranty: The statements made on this bulletin,
product labels or by any of our agents concerning this
material are given for information only. They are believed to
be true and accurate and are intended to provide a guide to
approved construction practices and materials.  As
workmanship, weather, construction equipment, quality of
other materials and other variables affecting results are all
beyond our control, Kelly-Moore Paint Company, Inc., does
not make nor does it authorize any agent or representative
to make any warranty of MERCHANTABILITY OR
FITNESS for any purpose or any other warranty, guarantee
or representation, expressed or implied, concerning this
material except that it conforms to Kelly-Moore's quality
control standards. Any liability whatsoever of Kelly-Moore
Paint Company, Inc. to the buyer or user of this product is
limited to the purchaser's cost of the product itself.

Bình luận sản phẩm

  • Đánh giá của bạn về sản phẩm:
  • reset captcha
  • Gửi bình luận

Danh sách bình luậnChưa có phản hồi về KellyMoore 98-001 (4 Lít) Sơn Lót Ngoại Thất Chống Kiềm (PH11).